For in vitro laboratory research use only. This article explains analytical chemistry terms. It makes no claims about the effects of any material.
A peptide is a chain of amino acids joined by peptide bonds. Each amino acid has a side chain, and some side chains are oily and avoid water while others are polar or charged and interact with it. Peptide hydrophobicity describes the overall balance of the two. This guide explains which amino acids are hydrophobic, how hydrophobicity scales work, how to calculate a GRAVY score by hand and how hydrophobicity relates to retention time in reversed-phase HPLC.
What hydrophobicity means
“Hydrophobic” literally means “water-avoiding.” A hydrophobic side chain is made mostly of carbon and hydrogen, such as the branched chains of leucine and isoleucine or the ring of phenylalanine. It has no charge and little ability to form hydrogen bonds with water. A hydrophilic (“water-attracting”) side chain carries a charge or polar groups such as –OH, –NH2 or –COOH.
For a whole peptide, hydrophobicity is not a single measured property. It is usually described in one of two ways:
- Calculated from the sequence, by adding up a value for each amino acid from a hydrophobicity scale.
- Observed in the lab, most often as how strongly the peptide is retained on a reversed-phase HPLC column.
The two usually point the same way, but they can disagree, as the sections below explain.
Hydrophobic and hydrophilic amino acids
The table lists the 20 standard amino acids with their three-letter and one-letter codes, their value on the Kyte-Doolittle hydropathy scale and a common grouping. Higher (more positive) values are more hydrophobic. Our guide to peptide sequence notation explains the codes.
| Amino acid | Three-letter | One-letter | Kyte-Doolittle value | Common grouping |
|---|---|---|---|---|
| Isoleucine | Ile | I | 4.5 | Hydrophobic |
| Valine | Val | V | 4.2 | Hydrophobic |
| Leucine | Leu | L | 3.8 | Hydrophobic |
| Phenylalanine | Phe | F | 2.8 | Hydrophobic (aromatic) |
| Cysteine | Cys | C | 2.5 | Polar or hydrophobic, depending on the source |
| Methionine | Met | M | 1.9 | Hydrophobic |
| Alanine | Ala | A | 1.8 | Hydrophobic |
| Glycine | Gly | G | −0.4 | Nonpolar (smallest side chain) |
| Threonine | Thr | T | −0.7 | Polar, uncharged |
| Serine | Ser | S | −0.8 | Polar, uncharged |
| Tryptophan | Trp | W | −0.9 | Hydrophobic (aromatic) in most textbooks |
| Tyrosine | Tyr | Y | −1.3 | Polar (aromatic) |
| Proline | Pro | P | −1.6 | Nonpolar |
| Histidine | His | H | −3.2 | Basic (partly positive near pH 7) |
| Glutamic acid | Glu | E | −3.5 | Acidic (negative at pH 7) |
| Glutamine | Gln | Q | −3.5 | Polar, uncharged |
| Aspartic acid | Asp | D | −3.5 | Acidic (negative at pH 7) |
| Asparagine | Asn | N | −3.5 | Polar, uncharged |
| Lysine | Lys | K | −3.9 | Basic (positive at pH 7) |
| Arginine | Arg | R | −4.5 | Basic (positive at pH 7) |
Textbooks group a few of these differently, especially glycine, proline, cysteine, tyrosine and tryptophan. The charged groupings depend on pH; our guide to peptide isoelectric point explains how side-chain charge changes with pH.
Hydrophobicity scales: Kyte-Doolittle and others
A hydrophobicity scale gives each amino acid a number. The Kyte-Doolittle scale, published in 1982, is one of the most widely used. Its values run from 4.5 for isoleucine to −4.5 for arginine, and the authors called the property “hydropathy.”
Many other scales exist. Some are based on how amino acids distribute between water and an organic solvent, and some are built from the measured reversed-phase HPLC retention of model peptides. They rank most residues in a similar order but differ in the details:
- Aromatic residues show some of the biggest differences. Tryptophan has a slightly negative Kyte-Doolittle value, yet it is one of the residues that adds the most to reversed-phase retention. Tyrosine shows a similar but smaller mismatch.
- Values from different scales can’t be mixed. Each scale has its own units and zero point, so a score is only meaningful next to scores calculated with the same scale.
A hydropathy plot (often called a Kyte-Doolittle plot) shows the average value over a short window of residues that slides along the sequence, so you can see which stretch of a chain is more hydrophobic. For a short peptide, a single average is usually enough.
How to calculate a GRAVY score
GRAVY stands for “grand average of hydropathy.” It is the sum of the Kyte-Doolittle values for all the residues, divided by the number of residues:
GRAVY = (sum of Kyte-Doolittle values) ÷ (number of residues)
How to read the result:
- A positive GRAVY means the sequence is hydrophobic overall.
- A negative GRAVY means the sequence is hydrophilic overall.
- The possible range is −4.5 (a chain made only of arginine) to 4.5 (a chain made only of isoleucine). Most mixed sequences fall well inside that range.
GRAVY has limits worth knowing:
- It ignores order. Two peptides with the same amino acids in a different order get the same GRAVY score.
- It ignores the ends and modifications. The free N-terminal amine, the C-terminal carboxyl and changes such as N-terminal acetylation or C-terminal amidation are not part of the calculation.
- It ignores pH. The Kyte-Doolittle values are fixed numbers, so the score doesn’t change with the conditions of a test, even though side-chain charge does.
Many online sequence calculators report a GRAVY score, and the hand calculation below shows what they are doing.
Hydrophobicity and reversed-phase HPLC retention
Reversed-phase HPLC is the method behind most peptide purity results. The column is packed with particles carrying a hydrophobic coating, commonly C18 (chains of 18 carbon atoms). The liquid that carries the sample, the mobile phase, usually starts as mostly water with a small amount of acid and moves to a higher share of an organic solvent, usually acetonitrile, over the run (a gradient).
A peptide sticks to the hydrophobic coating and comes off when the mobile phase contains enough organic solvent. In general terms:
- More hydrophobic peptides elute later. They need more acetonitrile to come off, so their retention time is longer.
- More hydrophilic peptides elute earlier. Peptides rich in charged and polar residues come off sooner.
- Retention is method-specific. Under the same method (same column, solvents, gradient, flow rate and temperature), the same compound comes off at about the same time. A retention time from one method can’t be compared with one from a different method. Our guide to reading an HPLC chromatogram explains retention time and peaks.
Retention depends on more than the GRAVY score:
- Charge and the acid in the mobile phase. At the low pH of a typical TFA-containing mobile phase, Asp and Glu side chains are mostly uncharged, while Lys, Arg, His and the free N-terminus carry a positive charge. Trifluoroacetate pairs with those positive charges, which tends to increase retention. Our guide to peptide counter-ions explains where TFA comes from.
- Sequence and shape. Where hydrophobic residues sit in the chain and how the chain folds can change how much of it touches the column. That is why two peptides with the same composition and the same GRAVY can elute at different times.
- Size. Longer chains usually have more contact with the column, so length matters as well as composition.
How hydrophobicity shows up in impurity peaks
Because a small change in structure changes hydrophobicity, many synthesis by-products elute close to the main peak, before or after it:
- Incomplete deprotection. A leftover protecting group, such as a tert-butyl group, makes the chain more hydrophobic, so the by-product often elutes after the main peak.
- Deletion sequences. A chain missing one residue often elutes earlier if the missing residue was hydrophobic. If it was a charged or polar residue, the by-product may elute later instead.
- Isomers. A diastereomer, with one residue in the opposite 3D form, has the same composition and GRAVY but can still elute at a slightly different time. Our guide to amino acid chirality covers why.
Our guide to peptide impurities lists the common by-product types and their mass changes.
A certificate of analysis doesn’t usually report hydrophobicity or a GRAVY score as a separate result. It reports the tests run on the sample, such as purity and identity. A certificate reports results for the sample tested. It is not a guarantee for other lots.
A worked example: calculating GRAVY
Here is an example with made-up numbers, not a real product. Take two made-up hexapeptides.
| Peptide | Kyte-Doolittle values | Sum | GRAVY (sum ÷ 6) |
|---|---|---|---|
| A: Ala-Leu-Lys-Gly-Phe-Ser (ALKGFS) | 1.8 + 3.8 − 3.9 − 0.4 + 2.8 − 0.8 | 3.3 | 0.55 |
| B: Ala-Glu-Lys-Gly-Asp-Ser (AEKGDS) | 1.8 − 3.5 − 3.9 − 0.4 − 3.5 − 0.8 | −10.3 | about −1.72 |
- Peptide A has a positive GRAVY, so it is hydrophobic overall. Peptide B has a negative GRAVY, so it is hydrophilic overall.
- On the same reversed-phase method, peptide A would usually elute later than peptide B.
- Now reverse peptide A to Ser-Phe-Gly-Lys-Leu-Ala (SFGKLA). The GRAVY is still 0.55, and the formula (C29H47N7O8) and monoisotopic mass (about 621.349 Da) are unchanged. Its retention time can still differ from peptide A’s, which is one reason HPLC separation is useful alongside a mass measurement. Our guide to LC-MS identity explains what a mass result confirms.
Frequently asked questions
What is peptide hydrophobicity?
It is how strongly a peptide’s side chains, taken together, avoid water. It is usually calculated from the sequence with a hydrophobicity scale or observed as retention in reversed-phase HPLC.
What is a GRAVY score?
GRAVY means grand average of hydropathy. It is the sum of the Kyte-Doolittle values for each residue divided by the number of residues.
What does a positive or negative GRAVY score mean?
A positive score means the sequence is hydrophobic overall; a negative score means it is hydrophilic overall. Scores fall between −4.5 and 4.5.
Which amino acids are hydrophobic?
On the Kyte-Doolittle scale, the most hydrophobic are isoleucine, valine, leucine, phenylalanine, cysteine, methionine and alanine. Textbooks differ on a few, such as tryptophan and glycine.
Why does a hydrophobic peptide elute later in HPLC?
In reversed-phase HPLC the column coating is hydrophobic. A more hydrophobic peptide holds on more strongly and needs a higher share of organic solvent to come off, so its retention time is longer.
Does a certificate of analysis report hydrophobicity?
Not usually as a separate result. A certificate lists the tests run on the sample, such as HPLC-UV purity and LC-MS identity. Check which tests a certificate lists.
Peptix certificates
The peptide lots with a published certificate on our peptide COA lookup page each have a third-party Certificate of Analysis showing the lot number, HPLC-UV purity and LC-MS identity. Where a certificate reports net content, the measured amount is printed on that certificate. For example, you can view the TB-500 10 mg, BPC-157 10 mg or BPC-157 / TB-500 20 mg product with its lot certificate, or browse all research peptides.
For research use only. Not for human or animal use.